Swedish Ceramic Institute – SCI
[ About SCI ] [ Staff ] [ Membership ] [ R&D ] [ About ceramics ] [ Courses ] [ Leaflets ] [ Publications ] [ Links ]

PhD theses

Other Publications

Engineering
Ceramics
2000–
1995–1999
1990–1994
1985–1989
1978–1984

Traditional
Ceramics
2000–-
1990–1999
1985–1989
1978–1984

 

 

Publications - Engineering Ceramics

2000-2006
2006
06-1kk  

Eriksson M, Andersson M, Adolfsson E and Carlström E, “Titanium-hydroxyapatite composite biomaterial for dental implants”, Powder Metallurgy, 49 [1] 70-77 (2006)
06-2kk

Eriksson M, Klein L C, Lidén E and Lindqvist K, “Preparation of nanoporous silica-zirconia layers by in situ sol-gel method”, Materials Science and Technology, 22 [5] 611-614 (2006)
  Palmqvist L, Lyckfeldt O., Carlström, E., Davoust P., Kauppi A., and Holmberg K, "Dispersion mechanisms in aqueous alumina suspensions at high solids loadings" Colloids and Surfaces A- Physicochemical and Engineering Aspects 274 (1-3) 100-109 (2006).
2005
05-1kk

Romano P, Lyckfeldt O and Khraisat W, “Water based processing of iron powder utilising starch consolidation”, Powder Metallurgy, 48, [2] 156-162 (2005)
05-2kk

Hansson K, Tang J E, Halvarsson M, Pompe R, Sundberg M and Svensson J-E,  “The beneficial effect of water vapour on the oxidation at 600 and 700 ° of a MoSi2-based composite”, J. Eur. Ceram. Soc., 25 [1] 1-11 (2005)
05-3kk

Eriksson M, Andersson M, Holmersson R, Berggren C and Carlström E, “On deformation control of dental crowns prepared by titanium powder process” Powder Metallurgy 48 (1) 103-109 (2005)
05-4kk

Carlström E, Palmqvist L and Lindqvist K, ”Ceramic processing for microsystem applications” pp 27-34 in 4M 2005, Proceedings of the First International Conference on Multi-Material Micro Manufacture, ed by W.Menz and S Dimov, Forschungszentrum Karlsruhe, Germany 2005
05-5kk Carlsson R, “Keramiska Material”, Mekanisten [1] 26 (2005)
05-6kk

Häggblad H-Å, Hockauf M, Eriksson M and Berggren C, ”Simulation of high velocity compaction of powder in a rubber mould with characterization of silicon rubber and titanium powder using a modified split Hopkinson set-up”, Powder Technology 154 [1] 33-42 (2005)
05-7kk

Palmqvist L, “Stabilization of aqueous ceramic suspensions with polyelectrolytes and hydrophilic copolymers”, Thesis Licenciate Engineering, Chalmers University of technology, Göteborg 2005
2004
04-1kk Eriksson M, Andersson M and Carlström E, “Titanium Dental Copings Prepared by a Powder Metallurgy Method: A Preliminary Report”, The Int . J. of Prosthodontics, 17 [1] 11-16 (2004)
04-2kk Eriksson M, Andersson M and Carlström E, “Cappette in titanio realizzate con la tecnologia della metallurgia della polvere: un rapporto preliminare”, La Rivista Internazionale di Odontoiatria Protesica (Edizione Italiana), 17 [1] 11-16 (2004)
04-3kk Adolfsson, E, “Keramer med fri form ger nya möjligheter”, Uppfinnaren & Konstruktören 3, 22-23 (2004)
04-4kk Eriksson M, Carlström E, Andersson M, Holmersson R and Berggren C, ”Density gradient in isostatically pressed titanium powder samples”, Powder Metallurgy, 47 [3] 273-277 (2004)
04-5kk Eriksson M, Häggblad H-Å, Berggren C, Andersson M, Holmersson R and Carlström E, ”New semi-isostatic high velocity compaction method to prepare titanium dental copings”, Powder Metallurgy, 47 [4] 335-342 (2004)
04-6kk Eriksson M, “Biomaterial Components Prepared by Titanium Powder Technology”, Ph D Thesis, Chalmers University of Technology/Swedish Ceramic Institute, Göteborg 2004
04-7kk Carlström E and Lindqvist K, “Development of Screen Printable Sensors with Templated Mesoporous Silica”, Ceram. Eng. Sci. Proc., 25 [4] 609-614 (2004)
04-8kk Lindqvist K and Carlström E, “Indirect solid freeform fabrication by binder assisted slip casting”, J. Eur. Ceram. Soc., in press, Corrected Proof, Available online 8 December 2004
04-9kk Lyckfeldt O, Rundgren K and Sjöstedt M, “ Freeze Granulation for the Processing of Silicon Nitride Ceramics”, pp. 281-284 in  Euro Ceramics VIII , Key Engineering Materials, Vols. 264-268, Part 1 (2004)
04-10kk Albinsson I, Bokalawela R, Dissanayake M A K L, Mellander B-E, and Rundgren K, ”Ceria-based electrolytes for intermediate temperature SOFCs – Electric and Dielectric Properties” pp. 1257-1260 in Euro Ceramics VIII, Key Engineering Materials, Vols, 264-268, Part 11 (2004)
04-11kk Hansson K, Halvarsson M, Tang JE, Pompe R, Sundberg M and Svensson JE, “Oxidation behaviour of a MoSi2-based composite in different atmospheres in the low temperature range 400-550 °C,” J. Eur. Ceram. Soc., 24 [13] 3559-3573 (2004)
2003
03-1kk Bowden M and Lyckfeldt O, “A Comparison of Potato and Corn Starch for Consolidation of Concentrated Zirconia Suspensions”, pp. 69–74 in Shaping II, Proceedings of the Second International Conference on Shaping of Advanced Ceramics, ed. by J Luyten and J-P Erauw, Vito Flemish Institute for Technological Research, Belgium 2003.
03-2kk Romano P, Lyckfeldt O, Candela N and Torralba J M, “Nitrogen Sintering of High Speed Steel Processed by Starch Consolidation”, pp. 369–374 in Materials Research Forum Vols. 416–418, Trans Tech Publications, Switzerland, 2003.
03-3kk Lyckfeldt O and Rundgren K, “Si3N4 Powders Applied for Water-based DCT”, pp. 47–62 in Ceramic Transactions, Vol. 142, “Silicon-Based Structural Ceramics for the New Millenium”, ed. by M. E. Brito, H.-T. Lin and K. Plucknett, The American Ceramic Society (2003).
03-4kk Eriksson M, Andersson M and Carlström E, “High Velocity Compaction of Titanium Powder”, pp. 301–304 in EURO PM 2003 Conference Proceedings Vol 1, EPMA, Shrewsbury, UK, 2003.
03-5kk Eriksson M, Andersson M, Adolfsson E and Carlström E, “Dense titanium-Hydroxyapatite Composite Biomaterial Prepared by High Velocity Compaction”, pp. 63–68 in EURO PM 2003 Conference Proceedings Vol 2, EPMA, Shrewsbury, UK, 2003.
03-6kk Romano P, Lyckfeldt O, Candela N and Velasco F, “Water-based Processing of High-speed Steel Utilising Starch Consolidation”, J. Mat. Proc. Techn., 143–144, 752-757 (2003).
03-7kk Adolfsson E, “Macro Porous Hydroxyapatite with Designed Pores”, pp. 1025–1028 in Bioceramics Vol 16, Key Engineering Materials Vols. 254–256, edited by Mário A. Barbosa, F. J. Monteiro, R. Correia & B. Leon,  Trans Tech Publications, Switzerland, 2003.
03-8kk

Lyckfeldt O, Käck D and Rundgren K, “Pressing and Sintering Development of Freeze-granulated Si3N4 Materials”, Ceram. Eng. Sci. Proc., 24 [4] 331–336 (2003).

03-9kk Holmquist M, Continuous Fibre Reinforced Oxide/Oxide Composites, Ph. D. Thesis, Ceramic Technology/Department of Materials and Surface Technology, Chalmers University of Technology, Göteborg 2003 (abstract)
2002
02-1kk Rundgren K and Lyckfeldt O, “Development of Water-based Processing of Silicon Nitride Materials”, Ceram. Eng. Sci. Proc., 23 [3] 3–10 (2002)
02-2kk Carlström E and Kristoffersson A, “Water-Based Tape Casting with Latex Binders”, Ceram. Eng. Sci. Proc., 23 [4] 3–14 (2002)
02-3kk Carlström E, Engebretsen C and Adolfsson E, “Designing and Fabricating Pores in Porous Materials”, Ceram. Eng. Sci. Proc., 23 [4] 235–245 (2002)
02-4kk Engebretsen C and Carlström E, “Binder Induced Porosity in Tape Casting”, Ceram. Eng. Sci. Proc., 23 [4] 253–259 (2002)
02-5kk Lyckfeldt O and Rundgren K, “High Solids Loaded Si3N4 Suspensions for Water-based DCT”. In Proceedings of CIMTEC 2002 – Part A (in press)
02-6kk Rundgren K and Lyckfledt O, “Sintering Performance and Properties of Pressed Si3N4 Materials”. In Proceedings of CIMTEC 2002 – Part B (in press)
2001
01-1kk Vandeperre L J, Kristoffersson A, Carlström E and Clegg W J, “Thermal Shock of Layered Ceramic Structures with Crack-Deflecting Interfaces”, J. Am. Ceram. Soc, 84[1]104-110 (2001)
01-2kk Kahlman L, Öjmertz K M C and Falk L K L, “Abrasive-waterjet Testing of Thermo-mechanical Wear of Ceramics”, Wear, 248 [1-2] 16-28 (2001)
01-3kk Legin Eyzop B and Karlsson S, “Contact Fatigue of Silicon Nitride”, Wear, 249, 208–213 (2001)
01-4kk Lyckfeldt O, Nordberg L-O and Nyborg L, “Processing of High-Speed Steel by Starch Consolidation”. Presented at 2000 Powder Metallurgy World Congress, Kyoto, Japan 001115 (2001)
01-5kk Pompe R, Halvarsson M, Kishi K and Lundberg R, “On the Mechanism of High Temperature Strength Degradation of Low-doped HIPed Silicon Nitride by In-depth TEM-SEM Investigation”, Ceram. Eng. Sci. Proc., 22 [3] 183–190 (2001)
01-6kk Tang J E, Halvarsson M, Hansson K, Svensson J-E, Li X-H and Pompe R, “Microanalysis on the Oxidation and Sulfate Attack of Partially Stabilized Zirconia Thermal Barrier Coating”, Ceram. Eng. Sci. Proc., 22 [4] 463–470 (2001)
01-7kk Eyzop B L and Karlsson S, “Influence of Glass Phase Composition and Microstructure on Wear Properties of Silicon Nitride”. Presented at 2nd World Tribology Congress, Wienna 3–7 September 2001 (2001)
01-8kk  Palmqvist L, Lyckfeldt O, Kauppi A, Andersson K and Davoust P, “Dispersion of Alumina with Different Polyelectrolytes”, pp. 25–28 in Euro Ceramics VII, Part 1 (extended abstracts), Key Engineering Materials, Vols. 206–213, Trans Tech Publications, Switzerland, 2001
01-9kk Lyckfeldt O, Palmqvist L and Peydemenge F, “Dispersing Si3N4 at High Solids Loading – Applied to Protein Forming”, pp. 75–78 in Euro Ceramics VII, Part 1 (extended abstracts), Key Engineering Materials, Vols. 206–213, Trans Tech Publications, Switzerland, 2001
01-10kk Carlström E and Kristoffersson A, “Water-based Tape Casting and Manufacturing of Laminated Structures”, pp. 205–210 in Euro Ceramics VII, Part 1 (extended abstracts), Key Engineering Materials, Vols. 206–213, Trans Tech Publications, Switzerland, 2001
01-11kk  Lindqvist K and Carlström E, “Green Machining of Alumina Formed by CIP, Starch Consolidation and Latex Slip Casting”, pp. 301–304 in Euro Ceramics VII, Part 1 (extended abstracts), Key Engineering Materials, Vols. 206–213, Trans Tech Publications, Switzerland, 2001
01-12kk Gustafsson S, Falk L K L, Pitchford J E, Clegg W J, Lidén E and Carlström E, “Development of Microstructure during Creep of Mullite and Mullite 5 vol% SiC Nanocomposite”, pp. 1145–1148 in Euro Ceramics VII, Part 2 (extended abstracts), Key Engineering Materials, Vols. 206–213, Trans Tech Publications, Switzerland, 2001
01-13kk Romano P, Lyckfeldt O, Candela N and Velasco F, “Water Based Processing of High-Speed Steel Utilising Starch Consolidation”, pp. 1339-1346 in AMPT ’01, New Developments in Powder Technology, Proceedings of the International Conference on Advanced Materials Processing Technologies, Volume III, Ed. J. M. Rorralba, Universidad Carlos III (2001)
01-14kk Carlström E, Carlinger L, Eyzop B, Kristensson A and Sjöstedt M, “Monitoring of Die Wear During Pressing of Steel Powders”, pp. 166–171 in EURO PM2001 Proceedings, Volume 3, European Powder Metallurgy Association, 2001.
01-15kk Magalhães S, Nyborg L, Lyckfeldt O and Nordberg L-O, “Sintering Cycle Design and Evaluation of High Speed Steel Starch Shaped Parts”. In 2001 Advances in Powder Metallurgy & Particulate Materials, Part 5 – Sintering, Sinter Hardening, De-Lubrication, Dimensional Change Control, MPIF, 2001. 
2000
00-1kk Legin Eyzop B and Karlsson S, "Influence of Microstructure on Contact Fatigue of Silicon Nitride", pp. 337-344 in Proceedings of the 1st International Conference on Tribology in Environmental Design 2000, ed. M Hadfield and C Ciantar, Pro­fessional Engineering Publishing Limited, UK, 2000.
00-2kk Legin Eyzop B and Karlsson S, "Contact Fatigue of Silicon Nitride", , pp. 176-185 in Proceedings of the 9th Nordic Symposium on Tribology – NORDTRIB 2000,  ed. P Andersson, H Ronkainen, and K Holmberg, The Finnish Society for Tribology, Finland, 2000.
00-3kk Hansson K, Halvarsson M, Tang J E, Svensson J E, Sundberg M and Pompe R, "On the Mechanism of MoSi2 Pesting in the Temperature Range 400–500° C", Ceram. Eng. Sci. Proc., 21 [4] 469-476 (2000).
00-4kk  Tang J E, Halvarsson M, Kvist A, Hansson K, Svensson J-E and Pompe R, "An Investigation of the Microstructure in the Pest Oxide of a MoSi2-based Composite", Ceram. Eng. Sci. Proc., 21 [4], 477-484 (2000).
00-5kk  Davis J B, Kristoffersson A, Carlström E and Clegg W J, "Fabrication and Crack Deflection in Ceramic Laminates with Porous Interlayers", J. Am. Ceram. Soc., 83 [10] 2369-74 (2000).
00-6kk  Lyckfeldt O, Brandt J and Lesca S, "Protein Forming – A Novel Shaping Technique for Ceramics". J. Eur. Ceram. Soc., 20, 2551-2559 (2000).

[ Back ] [ Up ] [ Next ]

 



Last update: 2007-07-24